Lithiation MXene Derivative Skeletons for Wide-Temperature Lithium Metal Anodes

Lithium (Li) metal, as an appealing candidate for the next-generation of high-energy-density batteries, is plagued by its safety issue mainly caused by uncontrolled dendrite growth and infinite volume expansion. Developing new materials that can improve the performance of Li-metal anode is one of the urgent tasks. Herein, a new MXene derivative containing pure rutile TiO₂ and N-doped carbon prepared by heat-treating MXene under a mixing gas, exhibiting high chemical activity in molten Li, is reported. The lithiation MXene derivative with a hybrid of LiTiO₂-Li₃N-C and Li offers outstanding electrochemical properties. The symmetrical cell assembling lithiation MXene derivative hybrid anode exhibits an ultra-long cycle lifespan of 2000 h with an overpotential of ≈30 mV at 1 mA cm⁻², which overwhelms Li-based anodes reported so far. Additionally, long-term operations of 34, 350, and 500 h at 10 mA cm⁻² can be achieved in symmetrical cells at temperatures of −10, 25, and 50 °C, respectively. Both experimental tests and density functional theory calculations confirm that the LiTiO₂-Li₃N-C skeleton serves as a promising host for Li infusion by alleviating volume variation. Simultaneously, the superlithiophilic interphase of Li₃N guides Li deposition along the LiTiO₂-Li₃N-C skeleton to avoid dendrite growth.     

Solvent fractionation of hard palm stearin to increase the concentration of tripalmitoylglycerol and dipalmitoyl-stearoyl-glycerol as substrates for synthesis of human milk fat substitute

This research aimed to produce triacylglycerols fraction rich in palmitic acid (PA) at the sn-2 position from hard palm stearin (HPS) through acetone fractionation. Fractionations were done at HPS-to-acetone ratios of 1:3, 1:5 and 1:7 (w/v) and at temperatures of 25, 30 and 35 °C for 3 h. Triacylglycerols with PA at the sn-2 position, such as tripalmitoylglycerol (PPP) and dipalmitoyl-stearoyl-glycerol (PPS), were concentrated in the solid fraction, obtained after separation by filtration. The optimal fractionation conditions were at a HPS-to-acetone ratio of 1:5 (w/v) and 30 °C. The total PPP and PPS content was more than 91%, with a corresponding yield of more than 59%. Triacylglycerols obtained were composed of more than 91% PA in which 88% were at the sn-2 position. Conclusively, the solvent fractionation is a suited alternative method for the preparation of triacylglycerols used for the enzymatic synthesis of 1,3-dioleoyl-2-palmitoylglycerol which is the main triacylglycerol for human milk fat substitute.     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

Binary Ti–Fe system. Part I: Experimental investigation at high pressure

The present work illustrates the effect of quasi-hydrostatic pressure on the positions and widths of the homogeneity ranges of the intermetallic phases TiFe and TiFe₂ at high temperatures. The experiments were performed with Ti–Fe diffusion couples that were heat treated in a multi-anvil press at 2.5 GPa. The solubility limits of the phases were derived from the concentration profiles that were measured using electron probe microanalysis. It was found that the homogeneity ranges of TiFe and TiFe₂ extend to higher titanium concentrations, if the pressure is applied. The positions of the phase boundaries of the intermetallics on the iron-rich side are not affected by the pressure. The accuracy of the experimental data including the homogeneity ranges and temperatures was verified by comparing the homogeneity ranges of β-Ti(Fe), α/δ-Fe(Ti) and γ-Fe measured in this study with the homogeneity ranges taken from literature. The pressure was calibrated using the pressure-induced phase transitions of bismuth.     

Coexistence of three ferroelectric phases and enhanced piezoelectric properties in BaTiO3–CaHfO3 lead-free ceramics

Perovskite ferroelectrics possess the fascinating piezoelectric properties near a morphotropic phase boundary, attributing to a low energy barrier that the results in structural instability and easy polarization rotation. In this work, a new lead-free system of (1-x)BaTiO₃-xCaHfO₃ was designed, and characterized by a coexistence of ferroelectric rhombohedral-orthorhombic-tetragonal (R-O-T) phases. With the increase amount of CaHfO₃ (x), a stable coexistence region of three ferroelectric phases (R-O-T) exists at 0.06 ≤ x ≤ 0.08. Both large piezoelectric coefficient (d₃₃～400 pC/N), inverse piezoelectric coefficient (d₃₃^*～547 pm/V) and planar electromechanical coupling factor (k_p～58.2%) can be achieved for the composition with x = 0.08 near the coexistence of three ferroelectric phases. Our results show that the materials with the composition located at a region where the three ferroelectric R-O-T phases coexist would have the lowest energy barrier and thus greatly promote the polarization rotation, resulting in a strong piezoelectric response.     

油基钻井液的封堵性能研究与应用

在涠洲12-1北油田一期工程中使用油基钻井液后事故率明显降低,但仍未能彻底解决涠二段硬脆性泥页岩井壁稳定性问题。对进一步加强油基钻井液的封堵能力进行了室内研究。通过在油基钻井液中引入超微细颗粒材料、纤维材料、变形材料和粘弹性材料,可大幅度提高其封堵能力。在涠洲12-1北油田二期工程中应用了加强封堵能力的油基钻井液,结果钻井施工非常顺利,几乎无井下复杂事故。室内评价及二期工程实践结果表明,增强油基钻井液的封堵能力对保持硬脆性泥页岩井壁稳定至关重要。     

强捻棉纱针织产品的性能研究

通过对强捻棉纱针织产品进行服用性能测试，得出强捻纱织物具有良好的服用性能。     

三相交流电动机启动过程参数数值模拟

提出一种进行模拟计算电动机启动过程中各参数的新方法。利用电机运行理论,结合物体定轴转动定律,推导出电机运行参数随时间变化的函数关系式。将计算公式离散化后,对电机启动过程运行规律进行求解。实例计算了一种型号潜油三相电动机启动时电动机定子电流、转子电流、激磁电流、扭转力矩、转速参数及效率参数等随时间或转差率的变化规律,其变化曲线与试验结果基本一致,说明提出的计算方法是有效、正确、适用的。     

Attribute Allocation and Retrieval Scheme for Large-Scale Sensor Networks

Wireless sensor network is an emerging technology that enables remote monitoring of large geographical regions. In this paper, we address the problem of distributing attributes over such a large-scale sensor network so that the cost of data retrieval is minimized. The proposed scheme is a data-centric storage scheme where the attributes are distributed over the network depending on the correlations between them. The problem addressed here is similar to the Allocation Problem of distributed databases. In this paper, we have defined the Allocation Problem in the context of sensor networks and have proposed a scheme for finding a good distribution of attributes to the sensor network. We also propose an architecture for query processing given such a distribution of attributes. We analytically determine the conditions under which the proposed architecture is beneficial and present simulation results to demonstrate the same. To the best of our knowledge, this is the first attempt to determine an allocation of attributes over a sensor network based on the correlations between attributes.